Kernow Oils - Lubricant Solutions

Filter Your Results...

Selected...

Also filter...

By Viscosity...

Compressor Oils

Castrol Aircol SR 32 - Synthetic rotary compressor lubricant - 2135

Castrol Aircol SR 32 - Synthetic rotary compressor lubricant - 2135

 

The Castrol Aircol™ SR compressor oil range of premium lubricants are designed for use in rotary screw compressors and are based on polyalphaolefin (PAO) fluids.


Application

Aircol SR is suitable for use in oil flooded rotary screw compressors operating under extreme climatic conditions, harsh environments and severe operating conditions where very high air discharge temperatures (> 100°C) are experienced. These oils are also suitable for use in compressor units operating at normal operating conditions, with the maximum air discharge temperature =/< 100°C, as defined by ISO 6743-3:2003.

For normal operating conditions, these products can be used for extended drain intervals up to 8000 hours.

Aircol SR range is fully compatible with nitrile, silicone, polyurethane and fluropolymer seal materials typically used in compressor units. It is not compatible with butadiene styrene (SBR) or ethylene propylene (EPDM) seals.

 

Aircol SR is classified as follows:
DIN 51506 classification - VDL
ISO 6743/3 - DAG, DAH and DAJ for rotary air compressors

Aircol SR grades meet the requirements of:
Atlas Copco 8000 hour oil drain interval
Kaeser
 

Pack sizes available - 20L & 208L

Discover More +
Castrol Aircol SR 46 - Synthetic rotary compressor lubricant - 2136

Castrol Aircol SR 46 - Synthetic rotary compressor lubricant - 2136


The Castrol Aircol™ SR compressor oil range of premium lubricants are designed for use in rotary screw compressors and are based on polyalphaolefin (PAO) fluids.


Application

Aircol SR is suitable for use in oil flooded rotary screw compressors operating under extreme climatic conditions, harsh environments and severe operating conditions where very high air discharge temperatures (> 100°C) are experienced. These oils are also suitable for use in compressor units operating at normal operating conditions, with the maximum air discharge temperature =/< 100°C, as defined by ISO 6743-3:2003.

For normal operating conditions, these products can be used for extended drain intervals up to 8000 hours.

Aircol SR range is fully compatible with nitrile, silicone, polyurethane and fluropolymer seal materials typically used in compressor units. It is not compatible with butadiene styrene (SBR) or ethylene propylene (EPDM) seals.

 

Aircol SR is classified as follows:
DIN 51506 classification - VDL
ISO 6743/3 - DAG, DAH and DAJ for rotary air compressors

Aircol SR grades meet the requirements of:
Atlas Copco 8000 hour oil drain interval
Kaeser

 

Pack sizes available - 20L, 208L, 1000L IBC

Discover More +
Castrol Aircol SR 68 - Synthetic rotary compressor lubricant - 2137

Castrol Aircol SR 68 - Synthetic rotary compressor lubricant - 2137


The Castrol Aircol™ SR compressor oil range of premium lubricants are designed for use in rotary screw compressors and are based on polyalphaolefin (PAO) fluids.


Application

Aircol SR is suitable for use in oil flooded rotary screw compressors operating under extreme climatic conditions, harsh environments and severe operating conditions where very high air discharge temperatures (> 100°C) are experienced. These oils are also suitable for use in compressor units operating at normal operating conditions, with the maximum air discharge temperature =/< 100°C, as defined by ISO 6743-3:2003.

For normal operating conditions, these products can be used for extended drain intervals up to 8000 hours.

Aircol SR range is fully compatible with nitrile, silicone, polyurethane and fluropolymer seal materials typically used in compressor units. It is not compatible with butadiene styrene (SBR) or ethylene propylene (EPDM) seals.

 

Aircol SR is classified as follows:
DIN 51506 classification - VDL
ISO 6743/3 - DAG, DAH and DAJ for rotary air compressors

Aircol SR grades meet the requirements of:
Atlas Copco 8000 hour oil drain interval
Kaeser
 

Pack sizes available - 20L

Discover More +
Castrol Aircol MR 46 - Rotary Screw Compressor Lubricant - 2145

Castrol Aircol MR 46 - Rotary Screw Compressor Lubricant - 2145

 

Synthetic compressor oil for both oil flooded and oil injected rotary screw compressors operating continuously at air discharge temperatures up to 90ºC. The product has been designed to meet service drain intervals of 4000 hours. The Castrol AircolTM MR compressor oil range of premium lubricants are formulated from highly refined mineral oils and novel additive technology to give outstanding antiwear and antirust performance to meet the requirements of Atlas Copco and similar types of compressor design.

ISO Viscosity and pack sizes available
AIRCOL MR 46 - 20L & 208L

 

 

Application

Aircol MR incorporates a carefully balanced antioxidant system providing improved oxidative and thermal stability giving “extended” service life for both oil flooded and oil injected rotary screw compressors operating continuously at air discharge temperatures up to 90ºC. The product has been designed to meet service drain intervals of 4000 hours. For intermittent or continuous operation with air discharge temperatures above 90ºC the manufacturers’ standard oil change periods should be used. The Aircol MR range is fully compatible with nitrile, silicone and fluropolymer seal materials.

 

Aircol MR is classified as follows:
ISO 6743-3 Compressor Oils
DAG and DAH for rotary air compressors
Aircol MR grades meet the requirements of:
Atlas Copco for 4000 hour oil life.

Discover More +
Castrol Aircol SN 68 - Synthetic Air Compressor Lubricant - 2161

Castrol Aircol SN 68 - Synthetic Air Compressor Lubricant - 2161

 

Castrol Aircol SN compressor lubricants are high quality synthetic diesters. For use in all types of air compressor, especially reciprocating and rotary screw compressors operating under severe or normal conditions.

 

Application

Castrol Aircol SN compressor lubricants were developed to cope with the severe operating conditions experienced in rotary screw, rotary vane and reciprocating air compressors operating at high compression ratios and high discharge temperatures. Under these conditions Aircol SN compressor oils offer much reduced carbon forming tendencies and extended oil life when compared to mineral oils due to their much higher oxidation resistance. In reciprocating units, Aircol SN grades have up to eight times the service life of mineral oils.

 

ISO Viscosity and pack sizes available
AIRCOL SN 68 - 20L
AIRCOL SN 100 - 20L

Discover More +
Castrol Aircol SN 100 - Synthetic Air Compressor Lubricant - 2162

Castrol Aircol SN 100 - Synthetic Air Compressor Lubricant - 2162

 

Castrol Aircol SN compressor lubricants are high quality synthetic diesters. For use in all types of air compressor, especially reciprocating and rotary screw compressors operating under severe or normal conditions.

 

Application

Castrol Aircol SN compressor lubricants were developed to cope with the severe operating conditions experienced in rotary screw, rotary vane and reciprocating air compressors operating at high compression ratios and high discharge temperatures. Under these conditions Aircol SN compressor oils offer much reduced carbon forming tendencies and extended oil life when compared to mineral oils due to their much higher oxidation resistance. In reciprocating units, Aircol SN grades have up to eight times the service life of mineral oils.

 

ISO Viscosity and pack sizes available
AIRCOL SN 68 - 20L
AIRCOL SN 100 - 20L

Discover More +
Castrol Aircol PD 32 - Air compressor lubricants - 2165

Castrol Aircol PD 32 - Air compressor lubricants - 2165

 

Castrol Aircol PD oils are a range of compressor oils, based upon highly refined mineral oils, which are intended for the lubrication of both reciprocating and rotary air compressors. For lubrication of rotors, bearings and gears in rotary compressors, especially the oil flooded screw type with lubricant drain cycles of up to 2000 hours under normal use.

 

Application

The Castrol Aircol PD grades are ashless oils recommended for the lubrication of rotors, bearings and gears in rotary compressors, especially the oil flooded screw type with delivery temperatures of up to 120°C. Castrol Aircol PD compressor oils have excellent oxidation resistance and low carbon forming tendencies and meet the requirements of the DIN 51506 VD-L classification of lubricants for compressors having air discharge temperatures up to 220ºC. Castrol Aircol PD compressor oils also have sufficient anti-wear performance, as measured in the FZG Gear Test, to allow their use in certain screw compressors where drive between the screws is transmitted by the rotor faces themselves. The modern tendency in air compressor design is towards higher capacities from smaller units, with higher loads and temperatures leading to greater demands upon the lubricant.

Castrol Aircol PD meets the requirements (for appropriate viscosity grade) of major compressor manufacturers such as Atlas Copco, Champion, Sullair, Compair/Broomwade, Ingersoll-Rand, Kaeser and Bauer.

 

Advantages

  • Excellent water separation characteristics which allow condensation to readily separate from the oil, minimising the risk of emulsions which could block the oil separator element.
  • Fully inhibited against corrosion which enables protection even when operating under humid conditions.
  • Good thermal stability, low volatility and low carbon formation reduces the risk of fire and explosion and leads to longer operating life (up to 2000 hours).
  • Low deposit forming tendencies extends oil change intervals and provides longer air filter life which contributes to a reduction in maintenance costs.
  • Excellent coalescing properties mean little carry over of oil in the air stream.

 

 

ISO Viscosity and pack sizes available
AIRCOL PD 32 - 20L & 208L
AIRCOL PD 46 - 20L, 208L & Bulk delivery
AIRCOL PD 68 - 4x5L, 20L & 208L
AIRCOL PD 100 - 20L & 208L
AIRCOL PD 150 - 20L & 208L

Discover More +
Castrol Aircol PD 46 - Air compressor lubricants - 2166

Castrol Aircol PD 46 - Air compressor lubricants - 2166

 

Castrol Aircol PD oils are a range of compressor oils, based upon highly refined mineral oils, which are intended for the lubrication of both reciprocating and rotary air compressors. For lubrication of rotors, bearings and gears in rotary compressors, especially the oil flooded screw type with lubricant drain cycles of up to 2000 hours under normal use.

 

Application

The Castrol Aircol PD grades are ashless oils recommended for the lubrication of rotors, bearings and gears in rotary compressors, especially the oil flooded screw type with delivery temperatures of up to 120°C. Castrol Aircol PD compressor oils have excellent oxidation resistance and low carbon forming tendencies and meet the requirements of the DIN 51506 VD-L classification of lubricants for compressors having air discharge temperatures up to 220ºC. Castrol Aircol PD compressor oils also have sufficient anti-wear performance, as measured in the FZG Gear Test, to allow their use in certain screw compressors where drive between the screws is transmitted by the rotor faces themselves. The modern tendency in air compressor design is towards higher capacities from smaller units, with higher loads and temperatures leading to greater demands upon the lubricant.

Castrol Aircol PD meets the requirements (for appropriate viscosity grade) of major compressor manufacturers such as Atlas Copco, Champion, Sullair, Compair/Broomwade, Ingersoll-Rand, Kaeser and Bauer.

 

Advantages

  • Excellent water separation characteristics which allow condensation to readily separate from the oil, minimising the risk of emulsions which could block the oil separator element.
  • Fully inhibited against corrosion which enables protection even when operating under humid conditions.
  • Good thermal stability, low volatility and low carbon formation reduces the risk of fire and explosion and leads to longer operating life (up to 2000 hours).
  • Low deposit forming tendencies extends oil change intervals and provides longer air filter life which contributes to a reduction in maintenance costs.
  • Excellent coalescing properties mean little carry over of oil in the air stream.

 

 

ISO Viscosity and pack sizes available
AIRCOL PD 32 - 20L & 208L
AIRCOL PD 46 - 20L, 208L & Bulk delivery
AIRCOL PD 68 - 4x5L, 20L & 208L
AIRCOL PD 100 - 20L & 208L
AIRCOL PD 150 - 20L & 208L

Discover More +
Castrol Aircol PD 68 - Air compressor lubricants - 2167

Castrol Aircol PD 68 - Air compressor lubricants - 2167

 

Castrol Aircol PD oils are a range of compressor oils, based upon highly refined mineral oils, which are intended for the lubrication of both reciprocating and rotary air compressors. For lubrication of rotors, bearings and gears in rotary compressors, especially the oil flooded screw type with lubricant drain cycles of up to 2000 hours under normal use.

 

Application

The Castrol Aircol PD grades are ashless oils recommended for the lubrication of rotors, bearings and gears in rotary compressors, especially the oil flooded screw type with delivery temperatures of up to 120°C. Castrol Aircol PD compressor oils have excellent oxidation resistance and low carbon forming tendencies and meet the requirements of the DIN 51506 VD-L classification of lubricants for compressors having air discharge temperatures up to 220ºC. Castrol Aircol PD compressor oils also have sufficient anti-wear performance, as measured in the FZG Gear Test, to allow their use in certain screw compressors where drive between the screws is transmitted by the rotor faces themselves. The modern tendency in air compressor design is towards higher capacities from smaller units, with higher loads and temperatures leading to greater demands upon the lubricant.

Castrol Aircol PD meets the requirements (for appropriate viscosity grade) of major compressor manufacturers such as Atlas Copco, Champion, Sullair, Compair/Broomwade, Ingersoll-Rand, Kaeser and Bauer.

 

Advantages

  • Excellent water separation characteristics which allow condensation to readily separate from the oil, minimising the risk of emulsions which could block the oil separator element.
  • Fully inhibited against corrosion which enables protection even when operating under humid conditions.
  • Good thermal stability, low volatility and low carbon formation reduces the risk of fire and explosion and leads to longer operating life (up to 2000 hours).
  • Low deposit forming tendencies extends oil change intervals and provides longer air filter life which contributes to a reduction in maintenance costs.
  • Excellent coalescing properties mean little carry over of oil in the air stream.

 

 

ISO Viscosity and pack sizes available
AIRCOL PD 32 - 20L & 208L
AIRCOL PD 46 - 20L, 208L & Bulk delivery
AIRCOL PD 68 - 4x5L, 20L & 208L
AIRCOL PD 100 - 20L & 208L
AIRCOL PD 150 - 20L & 208L

Discover More +
Castrol Aircol PD 100 - Air compressor lubricants - 2168

Castrol Aircol PD 100 - Air compressor lubricants - 2168

 

Castrol Aircol PD oils are a range of compressor oils, based upon highly refined mineral oils, which are intended for the lubrication of both reciprocating and rotary air compressors. For lubrication of rotors, bearings and gears in rotary compressors, especially the oil flooded screw type with lubricant drain cycles of up to 2000 hours under normal use.

 

Application

The Castrol Aircol PD grades are ashless oils recommended for the lubrication of rotors, bearings and gears in rotary compressors, especially the oil flooded screw type with delivery temperatures of up to 120°C. Castrol Aircol PD compressor oils have excellent oxidation resistance and low carbon forming tendencies and meet the requirements of the DIN 51506 VD-L classification of lubricants for compressors having air discharge temperatures up to 220ºC. Castrol Aircol PD compressor oils also have sufficient anti-wear performance, as measured in the FZG Gear Test, to allow their use in certain screw compressors where drive between the screws is transmitted by the rotor faces themselves. The modern tendency in air compressor design is towards higher capacities from smaller units, with higher loads and temperatures leading to greater demands upon the lubricant.

Castrol Aircol PD meets the requirements (for appropriate viscosity grade) of major compressor manufacturers such as Atlas Copco, Champion, Sullair, Compair/Broomwade, Ingersoll-Rand, Kaeser and Bauer.

 

Advantages

  • Excellent water separation characteristics which allow condensation to readily separate from the oil, minimising the risk of emulsions which could block the oil separator element.
  • Fully inhibited against corrosion which enables protection even when operating under humid conditions.
  • Good thermal stability, low volatility and low carbon formation reduces the risk of fire and explosion and leads to longer operating life (up to 2000 hours).
  • Low deposit forming tendencies extends oil change intervals and provides longer air filter life which contributes to a reduction in maintenance costs.
  • Excellent coalescing properties mean little carry over of oil in the air stream.

 

 

ISO Viscosity and pack sizes available
AIRCOL PD 32 - 20L & 208L
AIRCOL PD 46 - 20L, 208L & Bulk delivery
AIRCOL PD 68 - 4x5L, 20L & 208L
AIRCOL PD 100 - 20L & 208L
AIRCOL PD 150 - 20L & 208L

Discover More +